I am restoring a used aluminum boat [16 feet]. I need help and consultation with it. Please help.? - floor aluminum boat
Recently, I have a small boat and I am interested in land restoration, painting, and adding leather seats. For information, I am a girl of twelve years, and I worked on this project with my father. In addition, you know where to buy models for ship names. AKA. Super Snapper? And I, if possible, an approximate cost?
Sunday, December 13, 2009
Floor Aluminum Boat I Am Restoring A Used Aluminum Boat [16 Feet]. I Need Help And Consultation With It. Please Help.?
2 comments:
Ok
Re-ground is very simple. If the existing soil is not so bad, that could put three coats of epoxy, to seal up and down, stabilize and give many more years of service.
If the boards have gone too far, then use them as templates for new sections of the layers of sound quality similar or better cut rate than the old stuff. Even at the level of the plates with at least three layers of epoxy sealing and stabilizing. I use a wet on wet method - this is not a "wet", as such, but to gel so that the previous level, and tap "Next." This allows the epoxy to fully cover the base coat without sanding between coats to bring - I get at least three diapers a day using this method and processing of glass, with regard to the height of the roof with a fine brush on the bubbles. I use two pack linear polyurethane as a top layer, one or two hands - is a gel is applied, but not completely eliminated the final layer of epoxy grinding healed. I sprinkle sugar on to create the top layer of a compact and finish. How? Well, if the goal of fully curedTube surface, dissolve the sugar! Coffee Sugar better grip, raw sugar - white sugar is - powdered sugar until icing sugar and compliance with the best intentions. I have this technique for thirty years or more, now that good works with gelcoat.
Paint cans Hate alloys - aluminum, is of course very rapidly oxidized and then stabilized in a protective layer, which is as good as any other surface - with the added advantage that the corrosion is very clear and easy to fix the form. If I have an alloy Hull paint already painted, I would remove any flaking paint and possibly strip the surface - either a stripper or sanding. If the color is really addictive, while sand. Then the acid is acid washing the surface with hydrofluoric acid (phosphoric acid, citric acid and other work also) the use of high quality, protective gloves and goggles!
Of course, you can ignore for a friction alloy fuselage, the bit extraction.
Then everyone can decay and repairs can be welded. Acid clean all repairs. City rinse to neutralize acids. Let dry.
They shouldestablish as soon as possible with an etch primer to a chemical bond with the surface. Prime all bare alloy etch paint bits you want. Etch primer is very thin - not a table - can see through it. If you laid it on thick enough that you can not see through it, then it is, and will not work. Too expensive to lose anyway.
If you are satisfied with the condition of the body are able to prime, or go to the Preview layer. This will depend on which system you have chosen coating. Top propose two models available pack. Whatever system you choose to use describe the whole system - as in the instructions and have some problems, and the entire backup and support from the manufacturer. Expect not much help, even if the steps or the combination products - skip samples is easy to show if the target has been correctly applied or not, so do not try if you are sure to process your application!
I have experience in the upholstery or sign language.
The cost, which. I quickly for less than $ 500 in cash for the materials in this size boat up to several thousand or more are working specifically on the job. You get what you pay, they are not likely to get what you pay for.
E-mail if you require specific advice.
Good luck.
I just got a V-bottom 16 meters. Do not replace the floor because they did not. We went to a supplier of automotive paint. It took a little Ford tractor gray color and had more colors to it. We have 2 high fire. He received a blue light perfect for outdoor use. Synthetic color was a little thick, but dries to a hard surface is real, and very bright. The company knew of Rector seats auctioned on e-bay. Almost any color you ask. Took a couple of times a little more than $ 50. I collected them to avoid shipping costs. You can go safely to a sign company and get the letter. Most have developed a computer program letters. Select the font and what it means. Entry and make the letters for you and all your peel stick. The painting was only $ 8 per gallon and the seats were a little more than $ 50.
Post a Comment